Deprecated: Function set_magic_quotes_runtime() is deprecated in /home/aalpern/ on line 14
Adam's Amplifiers: Moonlight
Go to content Go to navigation
Wednesday January 4, 2006 by adam





The Moonlight, a 1-watt amplifier designed by Simcha Delft, was my first amp build, and responsible for getting me hooked on this hobby. I started looking around the Internet for low-wattage vacuum tube guitar amps, because my Music Man was just Too Damn Loud! I found a reference to the Moonlight circuit at Amptone, which eventually led me to AX84. I got one of Simcha Delft’s hand-wound Moonlight output transformers from Obsolete Electronics Once I’d succesfully built this amp, I was hooked.

I’ve since re-built my Moonlight 3 times in a variety of configurations.

12AU7 Output Modification

Inspired by a thread on the AX84 BBS, I added a 12AU7 output tube option to my Moonlight, with excellent (IMHO) results. See the Moonlight-12AU7-Schematic.pdf download link for the modified schematic. This option was eventually removed from my Moonlight, as I built the LunchBox as a dedicated 12AU7 amp, and to make room for the tube-driven reverb experiment.

Zener B+ Dropping Circuit

Capacitor Driven Reverb

The current incarnation of my Moonlight is a rebuild adding a capacitor-driven reverb circuit. I’d wanted to add reverb to an amp for a while, and wanted to try to keep the component down, and avoid needing to purchase another transformer if possible. To that ends I started looking at capacitor driven reverb circuits driving a high-input impedance reverb tank. Handily, my Music Man combo has such a tank (A 4FB3A1B – try it out in the reverb decoder; driven by op amps in the MM) which I could use. I looked at Ampeg, Traynor, and Univox schematics for ideas, primarily.


The input stage, phase inverter, and output stage are identical to the standard Moonlight. This schematic adds the reverb driver & recovery stages and a mix control to mix the reverb & dry signals. Still needs tweaking for the appropriate Dwell & Mix ranges. The changed impedances due to the reverb circuit also slightly change the overall character of the amp. It’s a bit brighter and raunchier than the “stock” Moonlight.

See the MoonVerb-Schematic.pdf download link (to the right) for the schematic.


Here’s the text of a message I posted to the AX84 BBS about the problems with this circuit.

1) As it stands at the moment you can’t turn the reverb all the way off. With the mix control all the way down there’s still a fair amount of reverb.

2) The Dwell control isn’t very useful at the moment because I haven’t tweaked its range. About the first 10% is useful, but above that there’s just too much signal driving the reverb tank, and the reverb signal is distorted. It’s actually a kind of interesting sound, but not very useful.

3) It leaves an unused triode in the 12AX7. there’s nothing really wrong with that, but I hate wasting triodes. I’m planning an update which will use it (see below)

4) Due to the resistive mixing of the dry & wet channels, it reduces the amount of gain driving the PI. And of course, with the way I’ve set up the mix control, as you turn the reverb up, you’re actually also turning the dry signal DOWN. So right now my Moonverb is a lot cleaner than the Moonlight.

What I’m going to try with this amp is driving the reverb with only 1 section of the 12AT7 and recovering with the other. Then using both sections of the 12AX7 as an anode mixer for the dry & wet signals. That way I can adjust the dry & wet levels independent of each other. It will retain the ability to make the wet signal louder than the dry, but hopefully without sacrificing the gain on the dry signal.

I’m also going to add a reverb tone control, as the reverb signal is pretty bright.


Like this article? Add it to!

  1. I have a schematic for a single-knob tonestack that you might be interested in. It’s from the Guild 100-J.

    Andy Rovner    Jan 10, 05:55 PM    #
  2. Hi Adam, Great site. I wanted to inquire with you about the Moonverb. I truly think that the Moonlight is one of the best guitar tones I have ever heard. I would like to add reverb to it as you did but clearly you have defined problems with your first attempt. I know you did this experiement some time ago so I was hoping that you may have resolved some of the issues? If so I would really like to get that updated schematic. Or even a quick description of the changes from your original schematic. I inquired about a year or two ago about this and you suggested building the firefly as a first build. I did so but still yearn for a moonlight reverb. Thanks again for your site and your time. Kind regards, SG

    SG    Feb 16, 06:35 PM    #
  3. Hello,
    I also have a “too loud” MM 210HD. I am keen to acquire /perhaps build a Brian May “Deacy” type amp. Can you suggest where I can start?
    regards Jon Gibson

    Jonathan Gibson    Mar 19, 09:25 PM    #
  Textile Help